ZENN Car Diagnostics and Programming Kit
If you have the GE IC3645SR7A353E1 Controller
Program Your ZENN Car to run at 35 MPH
Not sure which Controller you Have?
Click Here
This Cable is not for the Curtis AC Controller
Curtis Programming Information Here
Click to Enlarge
Kit Includes everything you need:
Service CD Includes:
- GE Sentry Software 4.07
- GE Operating and Maintenance Manual for your E1 Traction Control
- Data Base and 35 MPH Settings Files Courtesy of "Speed
Up Your
Zenn" Web Page
- 7 Page Detailed Programming Instructions
- Fused Power Cable to Power your E1 Controller while Programming
- 6 Foot Shielded DB9 Extension Cable
- Zenn Access Cable to connect to your Existing Zenn Programming Port
- All Kits are 100% Tested before Shipment
The GE Manual includes:
- Complete Theory Of Operation
- Elementary Wiring Diagrams
- 23 Pin Main Plug Function Listing
- Troubleshooting and Diagnostic Help
- Status (Fault) Code Explainations
- Complete Function Settings Guide
- Read, Print and Save Your original Settings
- Change and Download New Settings
- Access 16 Stored Fault Codes
- Monitor Several Parameters in Real Time For Diagnosing Vehicle Failures
- Graph Several Vehicle Parameters in Real Time
What Others Have said:
"Robert, SUCCESS !!!!!!!!!!!! I am driving 36mph and than the regen kicks in. What a difference 10mph makes.
Thanks for all your hard work and patients. I will send you the pics of the connections this weekend."
Dave
"Hi Bob, just wanted to let you know I got your cables and software for the ZENN today. I will say whoever makes
your cables for you does a top notch job—good crimps---solder—strain relief, good all the way around."
Mike
"Success! I used GE Sentry software, edited only Field 7 (to 76) and Field 13 (also to 76), and got 30 mph uphill and 34 mph on the
flat/downhill (indicated). I think I'll stay with these settings for a week or two to be comfortable before I get more aggressive.
The Zenn feels quicker off the line, so there must be some effect on acceleration. "
Fred
Just wanted you to know my Zenn now drives like I'd expect it to. At one point I had the car up to 50mph without even realizing it.
I now keep an eye on the speed and run the car in the lower 40s mph. All the materials arrived fast and are well made.
Everything worked perfect and I'm just tickled about never buying gas for that car. Thanks again !
JB
Read more about Programming and Hookup here:
"Speed Up Your Zenn"
This complete kit allows you to plug into your existing Serial Port with the Zenn Access Cable. You will power the controller using
the supplied Fused Power Cable. The GE Software will allow you to Read your existing settings, aprox 30 in all.
The supplied Data Base and Settings Files will allow you to Download new settings that will set your speed to 35 mph.
The Detailed Instructions take you step by step through the software and settings.
DB9 Serial Port Computer Connector
Click to Enlarge
PLEASE NOTE: This cable is a 9 Pin DB9 Serial Port Cable. Make sure your computer you plan to use has a True Serial Port.
The Serial Port on your computer will have 9 Male Pins, do not confuse this with the monitor connector.
I have used USB to Serial Converters, some work some don't, I have had good success with the
Hawking UC232S Make sure any you try has over 230kbps Data Transfer Rate.
I have also used the Cables Unlimited Model USB-2920, purchased from Tiger Direct for about $15.00
The USB-2920 was little harder to install.
Some have also used the SYBA PCMCIA Model SD-PCB-1S, with success, but I could not get it to work.
Some of the reviews also mentioned it worked well but very difficult to get operational.
We have been supplying Programming Kits for Electric Forklifts using GE Sentry Software since it was first a DOS program.
We are fully authorized by GE to distribute this software and it comes direct from GE.
See our other Kits here: Forklift Electronics Store
Purchase the Complete Kit Using PayPal's Secure Site
PLEASE NOTE: Certain Parameters should not be changed from Factory Settings,
Forklift Electronics Is Not Responsible for any changes made to your existing settings.
Curtis Programming Cable
If You have the T4 Series Control without a Data Port Plug, There is a Dedicated Kit For your Controller:
T4 Diagnostic and Programming Kit
If You have the T3 Series Control without a Data Port Plug, There is a Dedicated Kit For your Controller:
T3 Diagnostic and Programming Kit
If You have the T2 Series Control with a 12 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T2 Diagnostic and Programming Kit
If You have the T1 Series Control with an 8 Pin Data Port Plug, There is a Dedicated Kit For your Controller:
T1 Diagnostic and Programming Kit
Forklift Electronics
Home Index Page
2/2010